bevel造句

1、Add Inner Glow and Bevel and Emboss.
添加内发光和斜面和浮雕。

2、Spur gear or compound bevel gear attachments can be provided in any position shown in Figure 1.
如果采用正齿轮(SGA)或复合伞齿轮(BGA)附件，则可以在图1中显示的各个位置安装手轮。

3、The teeth on bevel gears can be straight, spiral or hypoid.
锥齿轮的齿可以是直齿、螺旋形或准双曲面。

4、The bevel of that picture frame was damaged.
那个镜框的斜角已被损坏了。

5、Studied on and designed the pneumatic system for the spiral bevel gear burnishing machine.
该气动在国内是首次研究应用于数控螺旋锥齿轮研齿机。

6、You will also learn about the use of the Taper object, Fillet option and Bevel function.
您还将了解锥度对象、圆角选项和斜角功能的使用。

7、A METHOD FOR DESIGN OF SMALL BEVEL NOZZLE OF ROCKET ENG INES
火箭发动机小斜切角喷管的设计方法

8、We need to apply the following Bevel and Emboss style to get there.
我们需要应用“斜面和浮雕”样式获取更好的效果。

9、The parametric modeling method for loxodrome normal circular-arc spiral bevel gear was presented.
给出了斜航式法向圆弧螺旋锥齿轮的参数化建模方法。

10、Use the image below for the values of the Bevel and Emboss.
用这个底层的图片为斜面与浮雕设置值。

11、an outward bevel around a door or window that makes it seem larger
能够让门或窗显得更大的一个开口的倾面。

12、Again, draw smaller circle shape. Add Bevel and Emboss and Gradient Overlay.
同样，画小圆圈形状。添加斜面和浮雕和渐变叠加。

13、bevel the edges of, to make a miter joint
斜切边缘，使成斜角拼接。

14、The theoretical analysis research of spiral bevel gear lapping with dynamic force is carried out.
该研究是国内首次对螺旋锥齿轮动态力研齿进行的理论分析研究。

15、Analysis of Cracks in Bevel Drive Gear of “EQ-153” Rear Axle
“EQ-153”汽车后桥圆锥主动齿轮裂纹分析

16、All valves can be furnished with handwheels, chainwheels and bevel gear handwheels and chainwheels.
所有阀门都可以配置手轮、链轮和锥齿轮手轮和链轮。

17、Supports shadow, Refection, Glow, 3D bevel etc. effects.
支持阴影，恢复体力，夜光，3D斜面等效果。

18、Bevel gears can be mounted at standard, 90, 180 or 270 degree mounting.
锥齿轮可以采用标准位置，90度、180度或270度位置安装。

19、It used bevel gears to transmit power to the prop.
它使用的锥齿轮转交权力交给道具。

20、When ordering bevel gear actuators, specify mounting position as second line information.
如果是订购锥齿轮执行器，请在第二行增加安装位置信息。

21、These drive the central propeller shaft through bevel reduction gears with a 2:1 reduction.
这些驱动器，中央螺旋桨轴通过减少锥齿轮2：1减少。

22、DESIGN FOR FORMING MOULD OF EPS PLASTIC PACKAGING OF EQ153 REAR BEVEL GEAR
EQ153后桥锥齿轮包装衬垫模具设计

23、Revolves, canned, the V-belt pulley organization, the CAM gear, the crank slide, the bevel gear.
旋转、罐装、槽轮机构、凸轮机构、曲柄滑块、锥齿轮。

24、After that, select Bevel and Emboss and just follow the image below.
在此之后，选择斜面和浮雕，只是按照以下的形象。

25、The drive advantages and technologic advantages of plastic bevel gear were analyzed.
分析了塑料斜齿轮的传动优点和工艺特点。

26、Shown here with a wooden handle. The bevel is set from a protractor.
这一款有一个木把手，斜角要卡在量角器上。

27、Experimental study on the error correction of spiral bevel gear.
螺旋锥齿轮误差修正试验研究。

28、P/M BEVEL GEAR IN 40kN JACK USED FOR CAR
轿车用40kN千斤顶粉末冶金圆锥齿轮

29、The bevel milling cutter for cutting groove of oil casing-pipes was designed.
设计了用于油气田管道坡口切割的角度铣刀。

30、The Construction Method of European Bevel Roof
欧式斜屋面工程施工方法

bevel翻译