fabrication造句

1、Design and Fabrication of 150 MHz SAWF on Li_2B_4O_7 Crystal Substrate
以Li_2B_4O_7为基片150MHzSAWF的设计与研制

2、Forging Fabrication of Tubular Tuyere End Socket
贯流式风口端头的锻造

3、The Sputtering Process for the Fabrication of CrSi Thin Film Resistor
溅射法制作CrSi薄膜电阻工艺技术

4、Design and fabrication of auricular prostheses based on rapid prototype technology.
基于快速成型技术的人耳赝复体的设计与制造。

5、A model to describe the fabrication is set up and discussed
建立了描述此方法的模型，并进行了讨论分析。

6、Fabrication study on the assembly technology of triode CNT-FED device
三极CNT-FED的封装技术制作研究

7、The fabrication of the triode CNT-FED with newcathode-pasting technology
新型阴极粘贴技术制备三极CNT-FED的研究

8、As a new micro fabrication technology, micro electroforming I.
微电铸，又称精密电铸，是一种全新的微细加工技术。

9、fabrication of integrated construction panel
整体壁板制造

10、The fabrication of multiplex high speed photocoupler is reported.
研制了一种多路高速光电耦合器。

11、The Fabrication of Fiber Grating Used in Gain-clamped EDFA
用于EDFA增益锁定的光纤光栅的制作

12、FABRICATION OF A PARTICLE DETECTOR WITH A TOTAL THICKNESS OF 25μg/cm~2
总厚度25微克/厘米~2的粒子探测器的制备

13、Fabrication and Properties of Al_2O_3-Ni Network Composites
Al_2O_3-Ni网状复合材料的制备及力学性能

14、Monitoring of equipment design and fabrication work.
跟踪及监督设备设计和制造过程。

15、Fabrication of Active Layer Used in 640×480 TFT|AMLCD
640×480 TFT-AMLCD有源层的制备

16、Fabrication of high performance sintered materials through PIM
用粉末注射成形(PIM)制造高性能烧结材料

17、Fabrication and Microstructural Evolution of the Semi-Solid Al-4Cu-Mg Alloy
半固态Al-4Cu-Mg合金的制备及微观组织演化研究

18、It's usually the hottest component and during the fabrication it probably had a lot of stresses.
它事实上是最热的组件，在制造过程中，它可能有很大的压力。

19、A model to describe the fabrication is set up and discussed.
建立了描述此方法的模型，并进行了讨论分析。

20、The fabrication process and application of silicon carbide mirror are presented.
综述了碳化硅反射镜材料常用制备方法的特点。

21、Study on the Fabrication and Performance of AgI/Ag Leak Hollow Wave Guide
AgI/Ag泄漏型空芯波导的制备及其性能研究

22、Fabrication of 3D Nextel~(TM) 720/Mullite at low temperature
PIP法制备3D Nextel~(TM) 720/Mullite复合材料

23、Fabrication Techniques and Technology for Emit Needle of LMIS
液态金属离子源发射尖的制备工艺与技术

24、Fabrication of LP Outer Cylinder for 350MW Steam Turbine
350MW汽轮机低压外缸的装焊制造

25、Fabrication of Pipe External Aligning Device with Hydraulic Jack
液压千斤顶式外对口器的制作技术

26、Effects of Fabrication Errors on the Performance of an EDG Demultiplexer
工艺误差对EDG器件性能的影响

27、Influences of plastics fabrication methods.
塑料制造方法的影响。

28、Fabrication of BST Thick Films Using a New Sol-gel Process
新型sol-gel技术制备BST0—3型厚膜

29、FABRICATION AND PROPERTIES OF C/BAS COMPOSITES
C/BAS复合材料的制备及性能

30、Progress in fabrication of C/C composites by thermal gradient CVI process
热梯度CVl制备C/C复合材料工艺技术研究进展

fabrication翻译